Browse Definitions :
Definition

ohm

What is ohm?

The ohm is the standard unit of electrical resistance in the International System of Units (SI). It's one of the derived units defined in the SI standard, which means it's based directly or indirectly on the standard's fixed constants. The ohm is a measurement of resistance between two points of a conductor when a constant potential difference of one volt (V) is applied to those points and a current of one ampere (A) is produced. In simpler terms, it's the equivalent of one volt per one ampere (V/A). The ohm is represented by the Greek letter omega (Ω).

Ohms are sometimes expressed in power-of-10 multiples to accommodate large quantities. For example, one kiloohm is equal to 1,000 (103) ohms, and one megaohm is equal to 1,000 kiloohms or 1,000,000 (106) ohms. In addition, ohms can be expressed in smaller quantities, such as the microohm, which is 0.000001 (10-6) of a single ohm.

Calculating resistance in DC circuits

The ohm applies to both direct current (DC) and alternating current (AC). With DC, the electric charge flows in only one direction and doesn't oscillate back and forth like AC power. Three important quantities are used to measure a DC charge:

  • Voltage (E). The difference in charge between two points, caused by the pressure that forces the current to flow. Voltage is measured in volts.
  • Current (I). The rate at which the current flows. Current is measured in amperes, which are also referred to as amps.
  • Resistance (R). The rate at which a material resists the current's flow. Resistance is measured in ohms.

These three quantities are directly related to each other, as demonstrated in Ohm's Law, which was introduced by Georg Simon Ohm (1789-1854), a German mathematician and physicist who experimented with electricity. The law states that there's a proportional relationship between voltage, current and resistance in an electrical circuit. Specifically, voltage equals current times resistance, or E = IR.

Using basic algebra, the formula can be rearranged to find any one of the three quantities, if two are known:

  • Voltage: E = IR
  • Current: I = E/R
  • Resistance: R = E/I

The letter V is sometimes used to represent voltage rather than E, but the meaning is the same for the purpose of calculating quantities. In either case, the process is straightforward. For example, a circuit can be set up with a 9 V battery and a small lightbulb. The circuit currently produces a 0.5 A current. The following calculations can be used to determine the resistance created by the lightbulb:

R = E/I

R = 9 V/0.5 A

R = 18 Ω

A component on a DC circuit has a resistance of 1 Ω when a potential difference of 1 V produces a current of 1 A through the component, so a 9 V circuit with a 0.5 A current has a resistance of 18 Ω. In this example, however, the resistance is attributed entirely to the lightbulb, but a circuit's conductor (e.g., copper wire) can also be a source of resistance, as can other components.

an electrical circuit
Diagram illustrating the basics of an electrical circuit.

Calculating resistance in AC circuits

Ohms are also used when measuring resistance in alternating current. Unlike DC power, AC oscillates in a sinusoidal waveform, and the electric current can reverse direction. For this reason, measuring resistance in AC circuits works differently from DC circuits because other components can inhibit a current's flow. Instead, the circuit's impedance must be measured, which considers not only resistance, but inductance and capacitance:

  • Inductance (XL). The amount of impedance that can occur when an AC charge generates an electromagnetic field (EMF) that opposes the current. A component such as an inductor is often used to generate inductance.
  • Capacitance (XC). The amount of electrical charge stored in the circuit. A component such as a capacitor is often used to generate capacitance.

Both inductance and capacitance are measured in ohms. Together, they're referred to as the circuit's reactance (X), which is also measured in ohms. Reactance is determined by using one of the following formulas to calculate the difference between inductance and capacitance:

  • X = XL – XC
  • X = XC – XL

The formula selected depends on whether inductance or capacitance is larger. The smaller amount is subtracted from the larger amount when determining the total reactance.

sine wave's wavelength
AC power, unlike DC power, oscillates in a sinusoidal waveform and the electric current can reverse direction.

The principles of Ohm's Law can be used to calculate a circuit's electrical quantities, but the formula must be modified to consider impedance, which is represented by Z:

  • Voltage: E = IZ
  • Current: I = E/Z
  • Impedance: Z = E/I

When an AC circuit contains resistance but no inductance or capacitance -- that is, no reactance -- it is treated as a DC -- so, simply plug in the resistance value for Z when calculating voltage or current. If there is reactance, the concept of root-mean-square (RMS) must be incorporated into the calculations. RMS is a mathematical method for defining the effective voltage or current of an AC sinusoidal wave. It's used to calculate a circuit's impedance:

Z= √(R2 + X2)

The formula requires that reactance (X) be calculated first, then square both resistance and reactance, add them together and find the square root of their sum. The value of Z can be plugged into the modified Ohm's Law formula. This approach can also be used when working with radiofrequency (RF) waves.

Explore how to create a more sustainable IT department, check out Power over Ethernet basics and learn about the types of batteries for IoT devices.

This was last updated in January 2023

Continue Reading About ohm

Networking
  • firewall as a service (FWaaS)

    Firewall as a service (FWaaS), also known as a cloud firewall, is a service that provides cloud-based network traffic analysis ...

  • private 5G

    Private 5G is a wireless network technology that delivers 5G cellular connectivity for private network use cases.

  • NFVi (network functions virtualization infrastructure)

    NFVi (network functions virtualization infrastructure) encompasses all of the networking hardware and software needed to support ...

Security
  • virus (computer virus)

    A computer virus is a type of malware that attaches itself to a program or file. A virus can replicate and spread across an ...

  • Certified Information Security Manager (CISM)

    Certified Information Security Manager (CISM) is an advanced certification that indicates that an individual possesses the ...

  • cryptography

    Cryptography is a method of protecting information and communications using codes, so that only those for whom the information is...

CIO
  • IT project management

    IT project management is the process of planning, organizing and delineating responsibility for the completion of an ...

  • chief financial officer (CFO)

    A chief financial officer (CFO) is the corporate title for the person responsible for managing a company's financial operations ...

  • chief strategy officer (CSO)

    A chief strategy officer (CSO) is a C-level executive charged with helping formulate, facilitate and communicate an ...

HRSoftware
  • HR automation

    Human resources automation (HR automation) is a method of using software to automate and streamline repetitive and laborious HR ...

  • compensation management

    Compensation management is the discipline and process for determining employees' appropriate pay and benefits.

  • HR technology (human resources tech)

    HR technology (human resources technology) is an umbrella term for hardware and software used to automate the human resource ...

Customer Experience
  • martech (marketing technology)

    Martech (marketing technology) refers to the integration of software tools, platforms, and applications designed to streamline ...

  • transactional marketing

    Transactional marketing is a business strategy that focuses on single, point-of-sale transactions.

  • customer profiling

    Customer profiling is the detailed and systematic process of constructing a clear portrait of a company's ideal customer by ...

Close